Divab
pm sent
boot
Printable View
Divab
pm sent
boot
I made one door for my OES standard that I put on the windy side and it really helps with this small tarp. It's large enough that it will almost close the whole end when It's pitched tight. There are a few pictures of it in action in my album if you want see. It looks just like jazilla's drawing. I also made a grizzbeak clone but find it harder to use. :)
Getting the outline curve seems pretty easy to just lay it out and place the RS over it and trace it with chalk. I'm going to get an old bed sheet and do a mock up 1st to see how it fits and looks.
When you have your addon door ready, do you just lay it over the trim of the end and sew it together? Or is there something special which I might be missing.
I really like the simplicity of the single piece doors! Nice work Jazilla and Myles to go. :cool:
OneThing - The doors as shown look to be removable, they are not permanently attached (although nothing to stop you if you wanted to go that route). Clip the top and side to the RL and either clip/stake the corners and you're done.
From miles album:
http://www.hammockforums.net/forum/a...pictureid=8356
http://www.hammockforums.net/forum/a...pictureid=8355
IF that is what you have I wonder if you would be better off just making a big rectangular tarp out of plastic or tyvek. With a hex tarp you have some flat on the sides to start with. With the diamond you will need to do more than just close in the ends. Going to be noisy but I would look at a blue plastic rectangle tarp where you can fold in the ends. Might be the cheapest and easiest way out.
The tarp door is used to keep mostly wind and wind blown rain out. The tarp should get the full brunt of whatever weather is thrown at me. Plus if the doors do get wet they are at the ends of the tarp and won't wet you or the hammock. Also they are pitched down so any water will flow right off of them.
DivaB, if I where making doors for that tarp I would make a pattern first and here is how you do that. Set up the tarp. Get some string or masons line. run a length of string from the ridge tie out to the point on the ground you want your door to stop. Run another length from there to your tie out point then back to the ridge tie out. Now measure it all and you have the basic shape of your door. Add seam allowance or use grosgrain. Don't forget to add a bit along the tarp so the pull out there covers the gap. Let me know if this is hard to understand and I will do a visual.
If I'm reading this right you are talking about sewing the door straight to the tarp? If you make your door/doors removable you can choose were to put them or not to use them at all. I always carry my one door in my tarp bag and if the wind is blowing I clip it on the corner that faces the wind. I use #0 S beeners on the upper and lower D rings and a length of shock cord going to the opposite end to close the gap and the stake out corner has a length of shock cord attached. This gets used as my 3 season tarp and when more protection is needed I will need to buy a tarp with doors attached. The removable door is only 3oz but if I made 3 more It wouldn't be worth it.
http://www.hammockforums.net/forum/p...pictureid=8355
I was looking to turn it into a 4 season with doors at both ends. I'm going to make a removable one as well to bring when I use the small tarp which came with my Hennessy Hammock. 3 ozs is worth it for the small tarp when one of those hard summer rains hits in the south.
I was going to have 2QZQ add the doors for me for a long distant hike I was going to do in 2012. However, I had surgery two weeks ago, and have several more so it killed me doing much of anything. So, I just learned how to thread a needle on a sewing machine which belonged to my mother. I think the sewed on doors will be lighter and easier to deploy in the long run.