Do you think that using more chambers say 10 would help avoid down compression versus 7 chambers on an underquilt. Will be using differential baffles also?
Do you think that using more chambers say 10 would help avoid down compression versus 7 chambers on an underquilt. Will be using differential baffles also?
Differential baffles will definitely help. Number of baffles depends on size and placement. Each baffle adds weight, too...so the specific design you're thinking about will determine what's most efficient. In general, though, more baffles will keep down from shifting more than it will help avoid compression.
“Republics are created by the virtue, public spirit, and intelligence of the citizens. They fall when the wise are banished from the public councils because they dare to be honest, and the profligate are rewarded because they flatter the people, in order to betray them.” ~Judge Joseph Story
- My site: http://www.tothewoods.net/
- Designer, Jeff's Gear Hammock / Pack Cover by JRB
IMPOSSIBLE JUST TAKES LONGER
I assume you mean migration and not compression when you area talking about using more baffles.
More baffles do indeed help keep the down in place. I (and I believe some of the other gear makers on here) have found that the more down you put into the quilt, the less you have to be concerned with it shifting enough to create dead or cold spots. Under normal conditions of course.
If you do have enough down in the quilt then adding more and more baffles just starts to add weight and time to the project. Of course this is just my take on the subject.
Using differential baffles is about the best way to avoid compressing the insulation.Will be using differential baffles also?
Edit: Beat me to it Jeff.....right on.
Last edited by stormcrow; 01-18-2010 at 22:17. Reason: I type slow
Owner/Founder at Hammockgear.com - Hammock Camping Outfitters
Home of the Burrow, the Incubator, and the Phoenix
on my first DIY underquilt, i'm having compression problems and a little bit of migration problems. i did used differential baffles. the inner shell chambers are 6 1/2" and the outer is 8". I thought that would be enough, but i don't believe so. i'm just trying to figure out the problem, so it doesn't happen again. My size is 5' 5" and 110 lbs, small build. maybe i should just measure my radius and go from there. any thoughts?
Owner/Founder at Hammockgear.com - Hammock Camping Outfitters
Home of the Burrow, the Incubator, and the Phoenix
the outer shell is the same length as the inner shell. is that the problem?
Is your outer shell longer than your inner one? It could just be pulling from the ends and compressing that way. I know a lot of people use the 1"-wider-on-the-outside rule of thumb, so I imagine 1.5" is fine. I just realized I have this problem on my quilt (outer shell not longer enough) I'm making and have yet to figure out how I'm gonna compensate.
Hope that helps,
Acer
Edit: Hah, beat me to the punch, Stormcrow.
Laherb: the quilt curves end to end also, and if the outer shell's not longer, it will pull up against the inner one and compress the down.
It's better to have it and not need it than need it and not have it.
Formerly known as Acercanto, my trail name is MacGuyver to some, and Pucker Factor to others.
It's not procrastinating, its proactively delaying the implementation of the energy-intensive phase of the project until the enthusiasm factor is at its maximum effectiveness. - Randy Glasbergen
Yes, The UQ should be "box" shaped with sides and ends the same width as the baffles. 2" baffles will result in 4" longer and wider outer shell after hem allowancesthe outer shell is the same length as the inner shell. is that the problem?
That is exactly right. I would add that that is the minimum the outer shell should be larger than the inner shell. I also make the outer shell longer throughout the length of the shell and not just on the ends to compensate for the thickness of the baffles.
I am not sure how clear I am being (probably not very)...sorry.
sc
Owner/Founder at Hammockgear.com - Hammock Camping Outfitters
Home of the Burrow, the Incubator, and the Phoenix
Your right, I should have said a minimum of twice the baffle height added to length and width of outer shell after hem allowance.
Clear as mud, the bad thing is I understand what your are sayingI also make the outer shell longer throughout the length of the shell and not just on the ends to compensate for the thickness of the baffles.
I am not sure how clear I am being (probably not very)...sorry.
Bookmarks