I recently discovered robic 1.7 is perfect for my back, and there are lots of color choices. Last weekend i made a new hammock of this fabric but cut it down to 62" finished width. Next one will be 60". I'm 5'4".
I recently discovered robic 1.7 is perfect for my back, and there are lots of color choices. Last weekend i made a new hammock of this fabric but cut it down to 62" finished width. Next one will be 60". I'm 5'4".
It definitely sounds like upping the fabric to 1.6 will help a lot
This I can do. I just bought a new section of CCF for my dogs and have a couple of their old beds left-over to try this with. I was wondering how I might do with a pad vs the UQ
I've tried both, and turning on my side, to little relief, mostly because it's the curl from pelvis to shoulder than from side to side
I started out with a Hennessy Expedition Asym (which is probably a 2.5 or something fabric) and then switched to a Dutch Netless Hexon 1.0 too to save weight and bulk... but have since switched again to a Little Shop of Hammocks Warrior which is in a 1.9 fabric.
I am also very weight-conscious and some of my backpacking trips have 10-15 mile days and plenty of elevation.
I would agree with the others, if I love the 1.9 (I am 180lbs, 5'11") you'll probably be much happier with a 1.6 and if you wake up less sore, those few extra ounces won't be noticed since you'll just feel better overall and start with more energy in the morning.
Just hit the order button for a Hexon 1.6. I really hope it helps. Despite the pain I still got much better sleep in the hammock than on the ground so I don't want to go back
I hope your new Hexon 1.6 gathered end works out. However, just to be clear, a bridge hammock does not have to be heavy -- especially for someone who is a petite 110 pounds...
I made a netless DIY bridge hammock from Hexon 1.0 with carbon fiber spreader bars that came in under 12 ounces from apex to apex. One made from Hexon 1.6 or 1.0 oz ROBIC would be better on your back but still quite light. As has been suggested, a bridge can provide a very flat lay.
With bridge hammocks, you do need to consider the change in weight to your entire sleep system. Depending on your environment and weather conditions, you may need a slightly bigger tarp, but any weight penalty is often offset by being able to use a much smaller and lighter underquilt.
Last edited by kitsapcowboy; 05-28-2017 at 10:46.
Smart graphic design for all your needs by BGD
Yes. My 1.4oz PolyD hammock is like sleeping on a board compared to my single layer Hexon 1.0. I liken the PolyD material to a firm mattress. It lacks the immediate cozy factor of a stretchy material (or softer mettress), but your joints thank you in the morning.
Sent from my SM-G900P using Tapatalk
Another thing to keep in mind is how you hang the hammock. Varying the amount of sag as can make a difference. Many of us find that having the foot end about 12" higher than the head end can be beneficial in several ways. I find that most often the impact of changes can't be fully realized until at least three consecutive days in the hammock. Jumping in an out while making changes gives only inital impressions. I'll admit though that some changes can have an immediate impact, which is what I'll speculate you'll find with the change to 1.6.
Yeah, I was keeping the "keep the foot end higher" rule in mind although I found 6" better. Even with trees as close as 5 large paces (I can't get much closer than that with an 11ft tarp) I struggled with getting the straps high enough to allow enough sag while still keeping me from brushing the ground...sometimes it sucks to be short. I was often hunting down branches or rocks I could move to get a little more height. I have a SRL on my hammock but I found that having more sag than the typical recommendation helped also.
I found everything about a gathered-end hammock comfortable in general, so a little more support for my back should make all the difference.
Bookmarks