Page 1 of 19 12311 ... LastLast
Results 1 to 10 of 184
  1. #1
    Senior Member SGT Rock's Avatar
    Join Date
    Nov 2006
    Location
    Maryville, TN
    Hammock
    Argon X90 Experimental hammock
    Tarp
    7'x9' cuben tarp
    Insulation
    Pads and quilts
    Suspension
    Kevlar + dynaglide
    Posts
    2,178
    Images
    92

    DIY Cuben Tarp - minimal sewing, using VHB Tape

    A friend of mine asked me to make him a Cuben Tarp. As some may know, I did mine using VHB tape for most of the work, keeping sewing to a minimum. I think it makes for a stronger tarp overall.

    So this time I made a video about it so you DIY guys can see how it is done. Maybe it will help some of you to think through a Cuben Tarp DIY project, maybe it will scare some of you off.



    http://www.youtube.com/watch?v=BiFy90s_Zng
    NO SNIVELING!
    www.hikinghq.net - Hiking H.Q.
    www.bmtguide.com - the BMT Thru Hiker's Guide

  2. #2
    Senior Member Dave10's Avatar
    Join Date
    Apr 2011
    Location
    Madison, AL
    Hammock
    HH
    Tarp
    HH Storm Hex
    Insulation
    Reflectix & pad
    Suspension
    Whoopie slings
    Posts
    106
    Where did you get your Cuban and what's the weight?
    War **** Eagle! Glory Glory Man United

  3. #3
    Senior Member SGT Rock's Avatar
    Join Date
    Nov 2006
    Location
    Maryville, TN
    Hammock
    Argon X90 Experimental hammock
    Tarp
    7'x9' cuben tarp
    Insulation
    Pads and quilts
    Suspension
    Kevlar + dynaglide
    Posts
    2,178
    Images
    92
    www.zpacks.com

    7.84 ounces (222 grams) for a 8'10"x11' tarp with all the cords for set up.
    NO SNIVELING!
    www.hikinghq.net - Hiking H.Q.
    www.bmtguide.com - the BMT Thru Hiker's Guide

  4. #4
    Senior Member MAD777's Avatar
    Join Date
    May 2009
    Location
    White Mountains, New Hampshire
    Hammock
    DIY, WBBB & Switchback
    Tarp
    HG cuben,OES Spinn
    Insulation
    DIY 3/4 UQ/TQ, UGQ
    Suspension
    Dynaglide / Dutch
    Posts
    10,950
    Images
    39
    Fantastic! Thanks for posting this Sgt Rock.

    I'm one of those DIY folks that's been sitting on the fence, trying to decide whether to jump into cuben or not. I definitely want the cuben gear, but I didn't want to mess up a bunch of expensive fabric either. This visual is what I needed. Thanks again!
    Mike
    "Life is a Project!"

  5. #5
    Senior Member
    Join Date
    Sep 2010
    Location
    Rochester, NY
    Hammock
    Hennesy
    Tarp
    various
    Insulation
    pads, foam
    Posts
    4,687
    Images
    17
    Nice video, thanks!

  6. #6
    Senior Member WV's Avatar
    Join Date
    Feb 2008
    Location
    southeast WV
    Hammock
    DIY
    Posts
    4,815
    Images
    208
    Great job. There is more good information on working with cuben in this video than any other source I can think of, by far. I like the way you did your tie outs. I'm still experimenting with mine, and I may well adopt your technique. Thanks!

    You're fortunate to have an assistant. I don't have that luxury, so I've had to find another way to do the long seams. What has worked best is to lay a 4' x 8' piece of masonite on the floor and put a 4' x 4' piece next to it, so I have a work surface 12' long. Then I put one half of the tarp down and pull it taut, fastening it at each end with weights and pieces of painters' tape. I use a long strip of blue painters' tape to mask the edge of the 1" edge that will be bonded, so I can apply the Primer 94 with a small paint brush. The throw-away foam brushes work fine. Then I apply the 9460 VHB tape to the primed area. Because the cuben is held flat, one person can do this quite easily. Then I remove the blue masking tape. Next, I prime a 1" strip on the other half of the tarp in a similar fashion. Then I put the primed edge of the second tarp half over the taped edge of the first half and fasten it in place with weights and tape at each end. The backing paper is still on the VHB tape, but everything is lined up for bonding. Then I carefully start peeling the backing paper off at one end, but instead of pulling it straight back in line with the edge, I pull it at an angle to one side, so I'm pulling it out from between the two sheets of cuben, which are already in contact. To get it started you need to move the weights and lift one corner of the top piece. Once a 3" end of the backing paper is free, you can roll the bond and put the weight back. Then roll the entire seam as you pull the backing out, with the roller following an inch behind the backing as it comes off. If I did have an assistant, I think I would still use this method, with the assistant pulling the backing paper, so I'd have two hands to hold the cuben down ahead of the bonding area and roll it tight immediately after. I use 1" wide tape. A single backing strip is easier to pull than two, but it can be done. It's possible to prepare the cuben by trimming the edge with a soldering iron along a metal straightedge just before applying the primer, but using a cutting mat and rolling cutter is just as easy. I have thought about a cutting mat that's 6" wide and 12' long, but I don't do enough of this stuff to justify the expense. (Besides, they don't exist.)
    Last edited by WV; 08-03-2011 at 08:08.

  7. #7
    Senior Member dragon360's Avatar
    Join Date
    Nov 2010
    Location
    Toronto, ON
    Hammock
    WBBB/TR, DIY, HH, SB DL, GT UL
    Tarp
    ID/OES/WB/WL
    Insulation
    HG/WB/Go-Lite/WB
    Suspension
    Whoopie/Straps/DW
    Posts
    4,704
    Images
    1
    Great video - was hoping a few DIY cuben vids would surface sooner than later!
    The key to immortality is first living a life worth remembering. - St. Augustine

    Some people feel the rain. Others just get wet.
    - Bob Marley

  8. #8
    Senior Member Perkolady's Avatar
    Join Date
    Nov 2006
    Location
    NE GA
    Hammock
    diy
    Tarp
    diy 9x11
    Insulation
    JRB No Sniveller
    Suspension
    CBs + DCs
    Posts
    1,093
    Images
    29
    Thanks for doing this video, SGT Rock! I was wondering about this project and that tape, but hadn't seen anything about it yet. WOW! What a project!

  9. #9
    Senior Member FLRider's Avatar
    Join Date
    Jun 2011
    Location
    Gainesville, FL
    Hammock
    DIY Gathered End
    Tarp
    DIY Asym
    Insulation
    DIY Modular Quilt
    Suspension
    Whoopies/MSH
    Posts
    4,471
    Images
    14
    Thank you, Sgt. Rock. I've been on the fence about making my own cuben drybags, and this definitely helped clear things up for me in several areas.

    A question, though: does the tape work with materials other than cuben (I know you taped the tie-outs with patches, but I'm unsure whether the tape was adhering to the 550 cord or to the cuben patches or both)? For example, Neoprene and nylon? Or do I need to find another type of adhesive and/or sew and then glue patches over the sewn parts?

    Also, thank you for your website; it was what originally got me to try hammock camping!

  10. #10
    Senior Member vinnya42's Avatar
    Join Date
    Jul 2011
    Location
    Boulder, Co
    Hammock
    Bridge Hammock
    Tarp
    DIY 12x8 silnylon
    Insulation
    DIY IX UQ
    Suspension
    Whoopies & Webbing
    Posts
    108
    This should be sticky'ed to this page...Great job with the instructions Sgt Rock!

    Cuben is just amazing!

    VInce
    Hang it high and God Bless!!

    Vince

  • + New Posts
  • Page 1 of 19 12311 ... LastLast

    Similar Threads

    1. DIY Cuben Tarp....all tape, no stitching.
      By ofuros in forum Do-It-Yourself (DIY)
      Replies: 16
      Last Post: 02-19-2023, 21:29
    2. DIY sil tarp with minimal sewing & Head strap
      By vinnya42 in forum Do-It-Yourself (DIY)
      Replies: 5
      Last Post: 09-02-2011, 21:04
    3. Cuben Fiber Tarp Tape... Help
      By Raul Perez in forum Weather Protection
      Replies: 4
      Last Post: 09-30-2010, 19:26
    4. Do you stitch or tape CUBEN?
      By TOB9595 in forum Fabrics
      Replies: 18
      Last Post: 06-10-2010, 07:46
    5. minimal tarp
      By Albert Skye in forum Weather Protection
      Replies: 20
      Last Post: 02-17-2010, 12:40

    Tags for this Thread

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •