Page 5 of 5 FirstFirst ... 345
Results 41 to 44 of 44
  1. #41
    GrizzlyAdams's Avatar
    Join Date
    Apr 2007
    GrizzBridge Ariel
    HG Cuben Winter
    DIY UQ
    Quote Originally Posted by landcruzr View Post
    Having many of the same issues , I set off to the basement to put all of these suggestions to good use- I started by consuming several of my most prized home brews-A holiday ale high in flavor and alcohol .....
    a most excellent story.

    This is what happens to me if I'm sewing after midnight, even bereft of buzz.

    I'm happy to report that my roller cutter maimed finger is healing nicely without infection. It won't be long before I'm back typing with all 10 fingers again.


  2. #42
    New Member
    Join Date
    Sep 2007
    Grizzly, that is, um, gristly. Next project: kevlar finger cozies!

    When I start a sewing project, I make sure the thickness of the needle is suited to the fabric I'm sewing (there may be a chart inside the sewing machine manual, but basically, the lighter or stretchier the fabric, the lower the needle number). I also hold the thread ends behind the presser foot when starting the seam, and turn the flywheel forward by hand so that the needle is in the fabric before giving it power. I practice on a doubled scrap of the same fabric before I start on the actual project. Depending on the thickness of the seam, I may need to lighten up on the presser foot tension or adjust the upper thread tension so that the loops of thread are not too loose. Despite all of this, I get the birdnest under the seam sometimes.

    I have one of the exclusive Nelco machines, sold only at Sears during the 1980s, so your machine may vary.
    Last edited by Boose; 01-11-2008 at 07:36. Reason: not awake yet

  3. #43
    New Member landcruzr's Avatar
    Join Date
    Dec 2006
    Ok Ok - I have to admit that the story is slightly ficticious - however after having all the problems with my vertically oriented gear driven thread injector(real men dont use sewing machines )I just decided to take it to the shop and give it a tune up- its an older machine and probably hasnt been looked at in some time!!! The ladies there were very helpful with tips and tricks!! and also gave lots of advise on settings and adjustments!!

  4. #44
    Senior Member Rat's Avatar
    Join Date
    Oct 2006
    Bertram, Texas
    DIY 126 x 60 Tablecloth
    JRB 10 x 11
    New River/Owhyee
    I have two machines; one circa 2004 and one circa 1945. I use the 1945 machine the most, I just like it better. However, on both machines I use the same method for my bobbin tension.

    I wind the bobbin and then I hold the thread, if the bobbin falls on it's own it is too loose, when I give it a little bounce and it drops a few inches (6 or so) it is just right. Clumping, knots or a mass of thread on the bottom is usually too little tension, but it could also be the speed the fabric is going through the dogs.

    If you don't have a walker foot then you need to 'slightly' pull the fabric throught the dogs to keep it from bunching.

    However, needle size, thread size and speed are easy to deal with once you have the bobbin tension set properly, that is the main thing.

    Unless the timing is off, I think this will help your situation the most.
    "I aim to misbehave." - Capt. Mal Reynolds
    Mind of a Rat Youtube Channel

Similar Threads

  1. sewing frustration
    By ih8mice in forum Do-It-Yourself (DIY)
    Replies: 9
    Last Post: 11-19-2010, 06:59
  2. sewing machine help
    By Buzzard217 in forum Do-It-Yourself (DIY)
    Replies: 21
    Last Post: 12-10-2008, 18:52
  3. Sewing Machine HELP!!
    By Hooch in forum Do-It-Yourself (DIY)
    Replies: 3
    Last Post: 12-02-2007, 05:27


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts