DIY Insultex Top Quilt

[NFA]

I'm going camping this weekend with a group of friends up into the High Peaks of the Adirondack Mountains of Northern New York, and in my ongoing attempt to cut weight from my pack am trying out something new for keeping warm...

I'll be hanging in a GT nano, protected by a hammock sock (made lovingly by Mac with some insultex in the lower parts), and this afternoon made a simple TQ out of some Insultex I recently bought...

I bought 3 yards of the stuff (about 50" wide), and made a simple 2' footbox in the bottom by doubling the bottom 2' back on itself and sewing it closed on the sides...that's it, nothing else...

I'll be interested to see how it works inside the hammock sock...the TQ folds up tiny and weighs almost nothing...

Jamie - nfa

[Newzy]

Hope you have enough warm clothing to wear in case it gets chilly.

[MAD777]

Here is my IX experience:
I made a two layer IX top quilt with footbox and sewed the ridges in both the top and bottom layers to create a dead space between them.
Took it out on weekend hike where it got into the 30's - no wind, no rain. I didn't have a sock, but, I nearly froze to death! Didn't get any sleep.

I hope you can fit a portable space heater inside that sock! If not, my advice is to take a back-up plan with you!

[NFA]

It's likely not going to get that cold, but my hammock sock works incredibly well at creating a microclimate and keeping me warm...

My thinking is that I'll use the TQ (top sheet really) to stop wind and the loss of body heat in an upwards direction, but I wanted to try not bringing a heavy sleeping bag...I'll be bringing insulating layers for daytime use anyway, and so thought I could make good use of those overnight as well...

I'm planning to sleep in long underwear and beanie and socks and gloves...it'll be fine...

Pics and report to follow...

[egrant5329]

Mad777
How did the ix breath for you. I keep seeing posts of people using it, but the manufacturers info says it is impermeable to moisture and is waterproof.

One of the reasons hammocks initially interested me is to get me off of the sleeping pad because I sweat against it.

[AaronAlso]

I'm not sure a TQ made souly of IX is going to be as effective as an IX UQ. Why, you ask? Gravity!. IX absolutely needs dead air space trapped between the layers to work effectively. In an UQ, using differentially cut layers with pleats creates the airspace and gravity allows them to stay open. However, with a top quilt gravity is working against you to close those air gaps and perhaps create cold spots. I imagine you would have to use a thin layer of lofting insulation between layers to hold the airspace open on a top quilt. That's just my speculation, I have no DIY experience with IX, yet, but I do have a firm grasp of the physics envolved.

BTW: IX isn't impermiable, I can breath through it, slightly. It is not waterproof, but pretty resistant. I've read several places that it seems to be more breathable & water resistant on 1 side than the other.

[Newzy]

I made a double layer IX TQ with a ripstop outter shell and a fleece inner lining with footbox and draw collar at the shoulders, too hot to use for anything above 30f , your right they don't breath well

[Desiel]

I made a double layer IX TQ with a ripstop outter shell and a fleece inner lining with footbox and draw collar at the shoulders, too hot to use for anything above 30f , your right they don't breath well

Wanna sell it?

[canoebie]

I have a 2 layer IX top quilt with breathable 1.1 oz ripstop on each side. I use it in the summer, in winter I use it as a sock over my hammock, works great. I leave a vent. The stuff is clammy as a TQ no matter what. Works great as a UQ though.

[MAD777]

While the raw material IX doesn't breathe, that's not what is used in quilts.
The quilt material is a single layer of IX with a layer of polyester scrim sewn to each side.
Therefore, the "package" has thousands of needle holes per square yard.
These holes allow a modicum of air through, but not a lot.

I agree that gravity is the enemy of an IX top quilt.
That's why I sewed 1/2" high ridges every 3.5" into the fabric in an attempt to keep the two layers apart.
I think that worked for the most part.

Newzy, I think your fleece liner helped out a great deal, plus a little more help from the nylon shell. My double IX top quilt was only two layers of IX - nothing else.