I have that model and I don't ever have trouble setting it up, it seems pretty straight forward. Then again I don't have the ENO straps, I don't know if that complicates it?
Having trouble understanding what you mean by "The ends were twisted and when I thought I had fix it and put the bars in it would be worse"? I can't figure out why they would be twisted in some way that you could not just intwist them? Can you post any pics?
Could you just lay it out in the house, flat on the flat on the floor, with the net side up and attached, and get things straightened out? It should just look like a big rectangle of cloth, with a net on top, laying there on your floor. Then you could practice putting the spreader bars in and see how it is supposed to work, while taking your time and being comfy indoors.
Then go out to your trees and try it there. OK, I don't know how the straps you have work. I take it you got this used with non stock straps? How ever yours works, hook up to the trees LOOSELY, leaving some sag, and making sure it is right side up with the net, or at least the Omni tape edges of the hammock, at the top and not towards the ground. Put the spreader bars in while it is still loose, or else it will be very hard to get the bars in. There are notches in the bars and rings on left and right side of each end of the hammock. These metal rings fit easily right into the notches on the ends of the spreader bars.
When the bars are end, tighten up the suspension on each end so that the distance is roughly equal to each tree and the net is pulled fairly tight, then ease off a few inches until there is just a hint of sag in the net, and the hammock edges are about butt or hip height.
http://www.jacksrbetter.com/shop/bea...ammock-deluxe/
Or, attache a line ( ridge line ) that won't stretch much between the 2 outer rings, with a distance of 9 feet 6" ( original non-zipper model only). When you hang it just snug that line up. When empty and looked at from the side, the center will be a little higher than the ends.
Put the head end about 6" higher on the tree than the foot end ( at least for original model).
Many folks hated that net, and I used to, but I grew to like it a lot.
First, attach it real good on at least on end. Leave the net covering just the foot end, maybe 1/4 of the hammock or even hanging over the foot end spreader, out of the way. Then when you get in, put your feet into the bottom of the hammock, grab the net and pull it over your head. Leaving the sides loose, attach the Omni tape ( Velcro like ) real well to the top right under the bar, and just let it drape down on the sides either inside or outside the hammock, while you gather your thoughts. Here is a surprise, 90+% of the time, the net just hanging loose like that will keep the mossies out. Mossies tend to go towards your breath, rising body heat or a light that ou might have habging from a ridgeline above the hammock. They probably won't fly down and back up under the net and back down into the hammock. So as long as you get the ends on good, you can at least relax for a minute.
Then if worried about ticks or that the mossies will sneak in, just grap the net on one side, pull up from the foot end towards your head real tight and touch the Omni Tape edges together. Repeat on the other side and on the head end. There will then be some slack in the net edges, just push them together. You are sealed in, the net should be well above your face, and you can bust back out real quick and easy.
Sorry, no video available, maybe some one else will have one.
Oh, DO NOT use the spreader bars to pull yourself up in the hammock, and don't hang heavy loads from them, they will bend!
EDIT: here are a couple that might help:
http://www.youtube.com/watch?v=iw2xSDChiA8
you get a good idea how the hammock looks set up:
http://www.youtube.com/watch?v=XBeVl...eature=related
http://www.youtube.com/watch?v=GnoFG...eature=related
Bookmarks