Page 1 of 5 123 ... LastLast
Results 1 to 10 of 42
  1. #1
    Senior Member
    Join Date
    Jan 2013
    Location
    Ohio
    Hammock
    DIY Tablecloth Double
    Tarp
    Hennessy Hex
    Insulation
    PLUQ, Wool, Down
    Suspension
    DIY Whoopies
    Posts
    175

    DIY, ummmmmm, almost everything

    So as I stated in my introductory thread earlier today, I'm looking to get into hanging. I looked at a whole ENO setup at REI, but after some research have decided to go the DIY route. I've ordered 2 tablecloths to make the hammock, but have a few questions from here. First of all, is it OK to run the static end of whoopie slings through a channel I sew into the ends, or would I be better off from a weight bearing/durability standpoint to just use a smaller cord and larkshead them on? Also, I am going to make a "fronkey" bugnet, and am considering the same style sock as well. What is a good material to use for the sock? I read that canvas is good, but I'm going to be placing an order with DIY gear supply anyway, so would like to get something from there. Would 70d be appropriate? I am not concerned about weight, this is going to be used as a motorcycle camping kit. Anyway, before being a gram weenie would make any sense for me, I would need to lose a few pounds off MY frame. Thanks!

  2. #2
    Senior Member MAD777's Avatar
    Join Date
    May 2009
    Location
    White Mountains, New Hampshire
    Hammock
    DIY, WBBB & Switchback
    Tarp
    HG cuben,OES Spinn
    Insulation
    DIY 3/4 UQ/TQ, UGQ
    Suspension
    Dynaglide / Dutch
    Posts
    10,950
    Images
    39
    Hi gothmog, you can attach the whoopies either way. The advantage of having a separate line through the channel is that you can remove the whoopies easily should they get wet, or you just want to transfer them to another hammock.

    Be sure to use climbing rated line for all parts of the suspension!
    Mike
    "Life is a Project!"

  3. #3
    Senior Member
    Join Date
    Jan 2013
    Location
    Ohio
    Hammock
    DIY Tablecloth Double
    Tarp
    Hennessy Hex
    Insulation
    PLUQ, Wool, Down
    Suspension
    DIY Whoopies
    Posts
    175
    Thanks. I'm ordering 1/8" Amsteel blue for the whoopies. Techline dyneema good for an adjustable ridgeline, Or should I just get extra amsteel?

  4. #4
    Senior Member goobie's Avatar
    Join Date
    Jul 2011
    Location
    SouthEastern WI
    Hammock
    Raven, SLD Streamliner
    Tarp
    Hanger11WB,WntrHvn
    Insulation
    HG,UGQ,JrB
    Suspension
    UCR's
    Posts
    2,081
    Images
    1
    Get yourself 40' of Amsteel and you should have enough for a pair of 6' whoopies and an adjustable ridgeline (7/64" is plenty strong)

  5. #5
    Senior Member
    Join Date
    Jan 2013
    Location
    Ohio
    Hammock
    DIY Tablecloth Double
    Tarp
    Hennessy Hex
    Insulation
    PLUQ, Wool, Down
    Suspension
    DIY Whoopies
    Posts
    175
    Is amsteel good for tree straps as well, if using toggles to connect woopies?

  6. #6
    Senior Member Dave-O's Avatar
    Join Date
    Dec 2009
    Location
    Maryland
    Hammock
    BIAS WW and DIY Bridge
    Tarp
    JRB 11x10 Cat Tarp
    Insulation
    Leighlo and JRB
    Suspension
    Whoopie Slings
    Posts
    249
    Images
    2
    No, you want to use tree straps made from 1" wide polyester webbing or similar material to avoid damage to the tree.

    See the DIY guide at DIY Gear Supply. You can also order the material from Scott's site.

  7. #7
    Senior Member TheBrewGuy's Avatar
    Join Date
    Aug 2012
    Location
    Cleveland OH
    Hammock
    BIAS WWM
    Tarp
    HG 4 Season Cuben
    Insulation
    All HammockGear
    Suspension
    Whoopies&DutchHook
    Posts
    154
    Hey gothmog. Welcome from Cleveland. The only reason you may NOT want to run the whoopie sling right through the channel is water dripping down the line. I larks head an Amsteel continuous loop through the channel then larks head the whoopie to the loop. This gives it a small drip point so water doesn't make it to the hammock. I made a DIY winter hammock with attached sock/top cover and I used the woodland camo 1.1 30d ripstop 1sts. It is breathable but traps some decent heat. Good luck with your project!

  8. #8
    Senior Member nuttysquirrel's Avatar
    Join Date
    Dec 2012
    Location
    Forest Grove, OR
    Hammock
    diy, hk2001,bmbh
    Tarp
    diy hex or aysym
    Insulation
    diy's,jarbidge!!!!
    Suspension
    whoops, ucr, dutch
    Posts
    1,435
    Images
    42
    i would use a plastic kids sewing needle for making the whoopies. it makes threading so much easier .i just made a set of 10' whoopies and tree straps.

  9. #9
    Senior Member TheBrewGuy's Avatar
    Join Date
    Aug 2012
    Location
    Cleveland OH
    Hammock
    BIAS WWM
    Tarp
    HG 4 Season Cuben
    Insulation
    All HammockGear
    Suspension
    Whoopies&DutchHook
    Posts
    154
    I've heard that a #5 knitting needle works perfect for making buries in 7/64 Amsteel

  10. #10
    Senior Member Dave-O's Avatar
    Join Date
    Dec 2009
    Location
    Maryland
    Hammock
    BIAS WW and DIY Bridge
    Tarp
    JRB 11x10 Cat Tarp
    Insulation
    Leighlo and JRB
    Suspension
    Whoopie Slings
    Posts
    249
    Images
    2
    I use .035" (#15) Malin Hard-Wire Stainless Steel Leader from Bass Pro Shops as a splicing tool for 7/64" Amsteel.

    If you're going to use continuous loops through your hammock's channels as MAD777 and TheBrewGuy suggest then you might want to look at getting a pair of Dutch's whoopie hooks. I just got a set and am going to install them on my hammock this weekend.

  • + New Posts
  • Page 1 of 5 123 ... LastLast

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •