Results 1 to 2 of 2
  1. #1
    Senior Member toygun's Avatar
    Join Date
    Apr 2012
    Location
    MS
    Hammock
    DIY DL
    Tarp
    Superfly
    Insulation
    AHE New River
    Suspension
    Whoopies
    Posts
    597
    Images
    1

    Hammock Swing tutorial

    Found this on facebook...thought it would give some of you folks some ideas. TONS of photos in the link.

    http://www.soyouthinkyourecrafty.com...wing-tutorial/


    "Hammock Swing Tutorial

    Posted under Tutorials
    By Missy

    *Tutorial by Wendy @ Crafty Goodies for her win of the Sunshine challenge of season 11*
    When we were emailed the list of themes for this season “Sunshine” was the one I was crossing my fingers that I’d make it to. It was the only theme that I knew immediately what I wanted to do, so needless to say I am beyond excited that you all liked it too!
    This will involve a trip to the hardware and fabric stores so here’s what you’re after:
    *nylon cording
    –I used 3 bags of 50 foot 5/16th rope
    2 in. diameter wooden dowel
    *A Carabiner Hook
    **both of these are weight based so think ahead to how
    much weight you will have in your swing and buy accordingly!!!
    2 yds of Fabric for the swing
    1 yd of co-ordinating fabric for the cushions
    **I used a heavy Duck Cloth for both that was 45 inches wide
    Measure and cut your fabric.
    Open up the fabric so you can see the whole piece. Fold it back over itself so you have a piece that measures 45 x 36. To cut the swing piece measure from the cut edge back toward the fold–you’re going to need every bit of those extra six inches at the fold!!!
    Cut a double layer of the swing fabric to measure 45 inches long by 33 inches wide,with right sides together, set aside for a few minutes.
    Use the extra strip of fabric to make the tabs for the side of the swing.
    Cut 14 pieces, each measuring 6 inches long by 3 inches tall.
    Sew all of the tab pieces.
    Fold the fabric in half, right sides together, so you have a piece that is now 6 inches long by 1.5 inches wide. Sew the tab closed along the 6 inch side using a 1/4 inch seam.
    **I double sewed all of my seams, if you have a serger just run it through there!
    Turn the tab right side out and fold in half matching up the cut ends.
    Your piece should now be 3 inches by 1.25 inches.
    Sew the ends shut so that you now have a sewn loop/tab.
    I made a rectangle at the bottom of each tab and then criss-crossed through the rectangle–these babies aren’t coming undone!
    Repeat that step 13 more times…

    Pin the tabs into place.


    Fold up the top layer of fabric along the 45 inch side. Measure up from the bottom one inch and pin a tab into place. Measure up 5 inches from the first tab and pin the second one into place. Measure up another 5 inches from the 2nd tab and add the third tab. Repeat this for the fourth and fifth tabs.Measure up 6 inches from the fifth tab and pin in place the sixth tab, and then measure up 7 inches to pin the last tab into place.

    This is after it’s been sewn and flipped, but shows the space between the tabs!
    Be sure the sewn edge of the tab lines up with the cut edge of the swing and all tabs point into the center of the swing.
    Replace the top layer of fabric, line up all edges, and then carefully remove the pins from the tab and replace them going through all three layers–top, tab, and bottom.
    Repeat on the other side of the swing!
    Sew the swing.
    Leaving the bottom open, sew a 1/4 inch seam along the side, top, and side of the swing. I then used that seam as my guide and ran a second seam another 1/4 of an inch in.
    Turn the piece right side out.
    Fold the bottom inch in, pin in place, and then iron all the edges flat.
    Sew a 1/4 inch seam around the entire piece. Use that seam as your guide and run a second seam around the swing, and then repeat to make a third seam.
    Remove the pins from the bottom edge and the base for your swing is done!
    Cut and tie the ropes for the swing.
    Cut the rope into the following pieces:
    swing bottom back: 4 pieces @ 92 inches long
    swing bottom middle: 2 pieces @ 88 inches long
    swing bottom front: 2 pieces @ 84 inches long
    back base: 2 pieces @ 78 inches long
    back mid: 2 pieces @ 66 inches long
    back top: 2 pieces @ 52 inches longThey tie into the swing tabs in the following order:
    Starting at the bottom, fold one length of rope in half.

    With the ends together, loop them around and through themselves to from a knot at the base of each piece. Use a flame to melt the ends of the rope ends.




    Slip the knotted end through the tab on the swing.

    Tuck the other end of the rope under the knot, but over the tab and pull until taught.



    Push the knot down onto the tab so that the fabric ends up on top of the knot.
    Move to the opposite side of the swing and tie that piece into place.Repeat with each remaining piece of rope until all 14 pieces are knotted onto the tabs.

    Add the crossbar.

    Measure in on the dowel 7 inches from each end and add a small screw. This will keep the rope from sliding in on the pole.

    Add the rope loops onto the pole starting at the top and working your way down. Do this for both sides of the swing.
    I had my hubby help with this part as his knot tying skills far surpass mine, but I held the swing up and level while he wrapped a scrap piece of rope around the loops twice and tied it together in an official Boy Scout square knot! I did cut and then burn the ends all by myself though.
    **Having a buddy also helps to make sure the swing hangs properly from the pole before you tie it. And then have to
    re-tie it because it’s totally lop sided…

    Hang the swing.

    Cut one last piece of rope 10 feet in length.

    Fold it in half, and then half again so that you are holding one loop and the two tails.

    Slide the carabiner onto the folded rope and tie a knot around it, securing it in place.
    Yeah, it’s different rope, that was the “trial and error” part–not enough nylon rope the first go around!

    Separate the two looped ends and tie a knot into each one leaving the loop big enough to slip over the end of the dowel but not too big that it slides right over the gathered ropes already on the crossbar.
    I slipped the loop onto the dowel before I pulled the knot tight so that I could adjust it to the dowel.


    Sew the cushions.
    Last step! Are you ready?
    I used an envelope casing for both cushions cause it’s quick an easy and makes washing the casings a breeze.
    (this is an ehow link if you need a little help with the casing)
    The bottom pillow fabric was cut to 45 inches x 21 inches and sewn with 1/2 inch seams at the top and bottom and has a 2.2 in overlap.
    The finished size is 21 x 20.
    *Just a little fyi, I used the salvage edges so I didn’t have to sew seams on the “envelope” part.
    The top pillow was cut at 45 inches x 16 inches. Again, sewn with 1/2 inch seams at the top and bottom, has a 3.5 inch overlap and uses the savage egdes as the overlap hem.
    Finished size is 20 x 15.
    Plop those babies into the swing and smile big because your new sunshine-enjoying swing is done!
    Oh ya! Happy dance time-
    Mine is currently hanging from a beam on my patio. We screwed an eye screw into the beam and then slipped the carabiner onto it. Pure happiness!
    Thank you so much for letting me share this with you and for all your thrilling votes! I really am just tickled that you liked it.
    Enjoy your swing and the summer sun…happy crafting!"
    "Only two things are infinite, the universe and human stupidity, and I'm not sure about the former."
    - Albert Einstein

  2. #2
    Senior Member samjaynes's Avatar
    Join Date
    Jan 2011
    Location
    Northern Utah
    Hammock
    TrekLight Double /DIY HH/DIY WBBB
    Tarp
    GuideGear 12'x12'
    Insulation
    JCP DIY UQ
    Suspension
    Whoopie Sling 7/64
    Posts
    387
    Too much floral print - I had to close the link :-)

  • + New Posts
  • Similar Threads

    1. Modern hammock stand/swing
      By kandrejk in forum General Hammock Talk
      Replies: 8
      Last Post: 07-21-2014, 22:43
    2. DIY Hammock Stand from Swing Set Brackets
      By ky chris in forum Do-It-Yourself (DIY)
      Replies: 4
      Last Post: 07-06-2013, 16:19
    3. Converted Swing Set into Hammock Hanger
      By hikerman2000 in forum Do-It-Yourself (DIY)
      Replies: 5
      Last Post: 05-12-2012, 11:18
    4. Swing Springs used in Hammock suspension
      By Armando in forum General Hammock Talk
      Replies: 4
      Last Post: 10-31-2011, 21:21
    5. Swing swing from Michigan
      By leroybrown in forum Introduce Yourself
      Replies: 24
      Last Post: 01-10-2010, 15:49

    Bookmarks

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •