In the first real rain I have used this tarp in I was let down. Leaks at 2 of the tie outs and I where the tarp pole mod touched the top. I don't see info on a recommended sealer on the WB site. Any recommendations?
In the first real rain I have used this tarp in I was let down. Leaks at 2 of the tie outs and I where the tarp pole mod touched the top. I don't see info on a recommended sealer on the WB site. Any recommendations?
Silnet or pertex flowable silicone sealant.
This isn't a case of the tarp letting you down so much as a case of not paying attention to (admittedly hard to find) details. It is a case of not reading the fine print for your product (same thing happened to me). I had the same experience my first night in the rain with my SF. Brandon should do a better job calling out the need for sealing of tie outs directly on the product page; it's too easy to miss and the subject comes up on the forum more often than it should. The only clue is a link from the SF product page to "Tarps 101".
From the bottom of the Tarps 101 section of the Warbonnet site (I added bold highlights for the relevant section):
Seam sealing
All our tarps incorperate low stretch polyester edge binding on the Ridgeseam, this means the ridge does not need any seam sealer, however if your tarp has panel pulls (SF, MJ, CB, GT) then you will want to seal the 4 panel pulls. You'll want a suitable silicone (like GE Siliocone II from the hardware store). Set up the tarp where you can leave it pitched for about 8 hours or so. Apply the thinnest possible layer of silicone (your finger works well) to the stiches (to the stitches only) on the underside of each panel pull (underside of tarp only), and leave the tarp setup till dry (4-12 hours depending on temperature).
Last edited by DanglingModifier; 09-30-2014 at 18:53.
It doesn't NEED sealed. the fold he sews into the ridgeline prevent leakage. applying the force of short pole pole mod on the ridgeline will let the water through, hence why it only came through the points where it made contact. This is half the reason I believe TT went with the long pole mod, to avoid contact with the ridgeline.
This is available at autopart stores
http://www.pepboys.com/product/details/1204672/
I just applied it to my tie-outs.
Did you end up getting wet?
Good lord! Just seal it with some Sil-Net and be done with it. Tarps, even ones that claim not to need sealing, NEED SEALING. Anyone who's been in the woods for more than an occasional car camping weekend trip will tell you that. Nothing wrong with the tarp, looks like inexperienced user error, to me. Complaining about this is like someone taking back their new hiking boots to REI because they kept falling off....even though they did not lace them up. It's not their fault for not knowing that. Blame it on the boot maker.
BF
Last edited by bigfoot2; 09-30-2014 at 19:29.
+1 on pertex flowable silicone. Works great.
My head is an animal
Mine certain DID need to be sealed on the tie outs when first purchased, without any use of a pole mod. Those stitches in the tie outs leaked all over me in only a moderate rain.
Harsh man. No need to rub his nose in it! I'd chase you down like a dog and really give you a lecture on sensitivity training except my boots keep falling off due to some manufacturing defect!
Hey bigfoot2, lighten up! If you look at his post you can tell that cjayflo is new to the hobby, after all it was his first rain hang. I learned to seal seams 47 years ago as a young scout after almost floating out of a brand new tent (oh what a cold miserable wet week-end that was). You learned too at some point in your experience. 30 years from now cjayflo will be able to pass the info on to another camper and he will have his horror story to tell. We all have to learn as we go.
Bookmarks