I making a Mirage Primaloft Quilt. His instructions call for 5 yards (15 feet). Is that so you can make two quits? It seems that half that length would be good for one quilt.
Printable View
I making a Mirage Primaloft Quilt. His instructions call for 5 yards (15 feet). Is that so you can make two quits? It seems that half that length would be good for one quilt.
You need enough for the top and bottom piece of DWR with the insulation in the middle like a big sandwich. For me that would make just over 12 feet or 4+ yards. The 5th yard is to account for that and seams.
I don't think I really understand how one puts a quilt together, and I cannot seem to find any directions with good pics.
I was going to start a quilt in the next couple weeks, and the more I read the less I know. Someone please direct me.
They are too bulky too expensive and I don't like Ray Jardine. He has great ideas, but I have my opinion of him.
One layer of DWR for the top shell - ~78"
insulation in the middle
One layer of DWR for the bottom shell - ~78"
Add in seam allowances (a few inches), account for loss of length as the insulation lofts (another few inches)...and you're looking at ~162" of DWR....or about 4.5yds. Use the leftovers for a matching stuffsack.
Good. Don't forget to make the original cuts longer than you want the quilt to be. If you want a 78" long quilt, that layer should be cut to 78" + 1" seam allowance on each end + loft allowance. So maybe 81" before you start sewing. Or 82" if you're making a thick quilt.
Take a look at Patrick's KAQ directions:
http://www.kickassquilts.com/MakeTOC.html
The Potomac is an underquilt, but that just means it's more complicated than a top quilt - you can get the parts you need and skip the stuff you don't.
As far as Jardine's kit, I can understand you not liking some of the stuff he has to say. Fact of the matter is, though, you can't get the materials you need to make his quilt for what he charges for the kit - AND it comes with nicely detailed instructions. And if you're that worried about bulk, you can modify his design to reduce bulk/weight, or just spring for down.
I am not using Polarguard 3d. I was going to use Primaloft Sport. I thought that I had figured out that I only need one layer for 40F, but now I am starting to doubt myself. I was originally going to use down, but being a vegetarian I had a big problem with this, and decided against it. It is worth the extra weight in my opinion. However, when I calculated everything out it seemed too light (11 oz for a 6'x4' underquilt).
The way I figured out the weight was:
Primaloft Sport has a a CLO=0.74 and basis weight of 3oz
Total CLO for 40F would be 2
2/.74=2.7oz of insulation per Sq.yd
So that would mean I need 1 layer of the Primaloft.
Total Weight of Primaloft=3oz/Sq. yd*(6ft*4ft)/(9Sq.ft/Sq. yd)=8oz
Weight of Fabric=1.1oz/Sq. yd*(6ft*4ft)/(9Sq.ft/Sq. yd)=2.9oz
For a total estimated weight of 10.9oz.
This seems entirely too light.
Hmmm, I was going by what Ayce had said on Thru-hiker. I think I will ask him what that is all about.
i added 3 really simplified drawings of quilt construction in the homemade gear gallery. if you go to that gallery, you can see all three along w/ what's written below them.
one is the most commonly used method where you sew three sides together w/ the insulation showing, then turn it inside out so the insulation is inside. then sew the remaining opening closed.
this gives you a nice looking, finished seam around the edge.
if you want a simpler version, you can use this meathod http://www.hammockforums.net/gallery...5/P2270003.JPG
you lay the three layers the way they will be in the finished quilt, then sew the edges, leaving enough extra of one of the shell layers to fold over & sew again to give another kind of finished edge.
note the suggestion of leaving extra width on the insulation & top shell to prevent compression when you pull the quilt around you.
You can bet on a good-sized quilt weighing somewhere between 18 and 28 oz. And according to AYCE, Climashield XP works better for a large project like a quilt anyway. At least go with something continuous filament - you don't want a sewn-through quilt. Unfortunately Polarguard 3D is hard to find right now.
The XP has scrim which ends up weighing more it seemed.
Man quilts are getting real popular. I had a buddy ask me why cause cause winter is almost over. I said its the DIY fever. He just looked at me with a puzzled look.
I do it anyway. She gets p.o.ed. You should see the look I get when I tell her we are not going to drive to the store and that we should walk. She says , but I hate the one that is near us, and I tell her that I don't want to spend the money on gas and I don't want to pollute. I end up driving half the time.
AYCE already has a pretty detailed thread on clo in his archives. Have a look through there and you'll get the info you need.
Question, instead of making draw string sleeves as Mirages has, why not just make a more tie outs ( 5 or so on the 60 inch ends)? It seems easier than making little tiny pockets for the draw string. Run one rope through the webbing, tie both ends off to a mini biner, and clip the mini biner it to the descending rings. How does that sound?
Or maybe drop the mini biner and just use toggles?