Search:

Type: Posts; User: AlumaTurtle

Search: Search took 0.05 seconds.

  1. I have used the stand with the mentioned...

    I have used the stand with the mentioned measurements and have had no signs of problems so I am going to try bringing the hang higher like you said will do it a little at a time and see if i can...
  2. Jeff-oh Would you please Help me figure my setup...

    Jeff-oh
    Would you please Help me figure my setup safety factor? My pole length is 112 inches, 79 inch base, and a tip to tip length of 152 inches not counting the 2 inches past the point where the...
  3. Replies
    28
    Views
    108,930

    I ordered this shrink tube and find that after...

    I ordered this shrink tube and find that after shrinking it made the 3/4" tube too big to fit in the 1" tube. read in a post that someone else had the same problem. any ideas on how to shrink down...
  4. Replies
    15
    Views
    430

    [QUOTE=rasidi;1990334]Yeah, both for me too - for...

    [QUOTE=rasidi;1990334]Yeah, both for me too - for ease of setup and take down ..
    What he Said!!!
  5. Replies
    10
    Views
    3,907

    Thanks for your answer inquiring mind wanted to...

    Thanks for your answer inquiring mind wanted to know! I will feel better using, and implementing the Mod!!!!
  6. Replies
    10
    Views
    3,907

    Doesn't the ucr have less strength than a woopie,...

    Doesn't the ucr have less strength than a woopie, when taken down to one length than the two in a woopie?
  7. Please for a noob can you please elaborate a...

    Please for a noob can you please elaborate a little on head-left orientation Vs head-right orientation.
  8. Replies
    28
    Views
    108,930

    Ok! First Hang went well. Laid in the hammock for...

    Ok! First Hang went well. Laid in the hammock for abt 30 Min. I think i will want to upgrade to at least a 10 footer.

    Some questions. when laying in the hammock the center line came about mid...
  9. Replies
    28
    Views
    108,930

    I jumped the gun when taking pictures. I wanted...

    I jumped the gun when taking pictures. I wanted to Brag on my Handy work before it was done!You were right both perspective at work here the ground where the head end is about 12 inches higher the...
  10. Replies
    28
    Views
    108,930

    That was just on there while i was adjusting the...

    That was just on there while i was adjusting the ridge line. it kept tacoing while i was trying to adjust the foot end, and 45 degree angle of the poles.
    i am not even ready to test a hammock on it....
  11. Replies
    28
    Views
    108,930

    Well Its done except for final Adjustment. Still...

    Well Its done except for final Adjustment. Still have lots of fine tuning, as pictured each pole is 130" the center section of each pole is 60" of 1" EMT the two 3/4 end poles are 40 ". The fittings...
  12. Replies
    1,073
    Views
    210,006

    Perfect Thanks that is what i was thinking. Just...

    Perfect Thanks that is what i was thinking. Just couldn't picture in my mind. looks like i need to shorten my poles by an inch or so the holes on mine are 3" from the end. I looked for the soft...
  13. Replies
    1,073
    Views
    210,006

    copper-tube grommets as in the end holes could...

    copper-tube grommets as in the end holes could also serve as shims for the overlaps. Hard enough to be durable and slide freely, soft enough to be peened down to the micron level to make a good slip...
  14. Replies
    28
    Views
    108,930

    I am progressing well on my build quickly. I have...

    I am progressing well on my build quickly. I have Question about joining the apex and ground parts of the poles. I am thinking of using Soft shackle loop for connecting the ends. need help in knowing...
  15. Replies
    28
    Views
    108,930

    I am Looking to copy your tensahedron. would like...

    I am Looking to copy your tensahedron. would like to have an update on how the stand is holding up.
    I Am 175lb so am lighter but concerned with something i read about the pole flexing in the middle....
  16. Replies
    205
    Views
    100,549

    Sticky: [QUOTE=75RR;1143101]Hi, Have been working for a...

    [QUOTE=75RR;1143101]Hi,
    Have been working for a while on a Knot Pamphlet

    Great Information
    Thanks
  17. Question about Woopie String/ Ridgeline.

    Being new and Trying to Get a handle on ridgelines. I have been watching a lot of videos. Let me first say I weigh 170lbs. if i am reading the suggested weight limit for a "7/64 blue Amsteel" is 320...
  18. Replies
    5
    Views
    124

    You're pretty close to Lake of the Ozarks State...

    You're pretty close to Lake of the Ozarks State Park. About 18 Miles
  19. Replies
    9
    Views
    438

    Hi Neighbor! Almost the same way i got...

    Hi Neighbor!
    Almost the same way i got started!!! on the other side of the Lake from you!
    AlumaTurtle.
  20. Replies
    5
    Views
    124

    Another New one from Missouri!

    Well another new Missouri hanger gets added to the group! I might be the oldest new member of the [email protected] years young,at least my mind still thinks I am young!

    I was first introduced to hanging...
Results 1 to 20 of 21