[QUOTE=litetrek;2002092]Just ordered. Good value.
Can you or someone add a link to this product? I have looked at their site several times and unable to find it. Thanks in Advance
Type: Posts; User: AlumaTurtle
[QUOTE=litetrek;2002092]Just ordered. Good value.
Can you or someone add a link to this product? I have looked at their site several times and unable to find it. Thanks in Advance
What about this?
Lead Mine Conservation Area Jakes Creek Trail
I have used the stand with the mentioned measurements and have had no signs of problems so I am going to try bringing the hang higher like you said will do it a little at a time and see if i can...
Jeff-oh
Would you please Help me figure my setup safety factor? My pole length is 112 inches, 79 inch base, and a tip to tip length of 152 inches not counting the 2 inches past the point where the...
I ordered this shrink tube and find that after shrinking it made the 3/4" tube too big to fit in the 1" tube. read in a post that someone else had the same problem. any ideas on how to shrink down...
[QUOTE=rasidi;1990334]Yeah, both for me too - for ease of setup and take down ..
What he Said!!!
Thanks for your answer inquiring mind wanted to know! I will feel better using, and implementing the Mod!!!!
Doesn't the ucr have less strength than a woopie, when taken down to one length than the two in a woopie?
Please for a noob can you please elaborate a little on head-left orientation Vs head-right orientation.
Ok! First Hang went well. Laid in the hammock for abt 30 Min. I think i will want to upgrade to at least a 10 footer.
Some questions. when laying in the hammock the center line came about mid...
I jumped the gun when taking pictures. I wanted to Brag on my Handy work before it was done!You were right both perspective at work here the ground where the head end is about 12 inches higher the...
That was just on there while i was adjusting the ridge line. it kept tacoing while i was trying to adjust the foot end, and 45 degree angle of the poles.
i am not even ready to test a hammock on it....
Well Its done except for final Adjustment. Still have lots of fine tuning, as pictured each pole is 130" the center section of each pole is 60" of 1" EMT the two 3/4 end poles are 40 ". The fittings...
Perfect Thanks that is what i was thinking. Just couldn't picture in my mind. looks like i need to shorten my poles by an inch or so the holes on mine are 3" from the end. I looked for the soft...
copper-tube grommets as in the end holes could also serve as shims for the overlaps. Hard enough to be durable and slide freely, soft enough to be peened down to the micron level to make a good slip...
I am progressing well on my build quickly. I have Question about joining the apex and ground parts of the poles. I am thinking of using Soft shackle loop for connecting the ends. need help in knowing...
I am Looking to copy your tensahedron. would like to have an update on how the stand is holding up.
I Am 175lb so am lighter but concerned with something i read about the pole flexing in the middle....
[QUOTE=75RR;1143101]Hi,
Have been working for a while on a Knot Pamphlet
Great Information
Thanks
Being new and Trying to Get a handle on ridgelines. I have been watching a lot of videos. Let me first say I weigh 170lbs. if i am reading the suggested weight limit for a "7/64 blue Amsteel" is 320...
You're pretty close to Lake of the Ozarks State Park. About 18 Miles
Hi Neighbor!
Almost the same way i got started!!! on the other side of the Lake from you!
AlumaTurtle.
Well another new Missouri hanger gets added to the group! I might be the oldest new member of the group@75 years young,at least my mind still thinks I am young!
I was first introduced to hanging...