Results 1 to 1 of 1
  1. #1
    Papatechie's Avatar
    Join Date
    Aug 2017
    Location
    Virginia
    Hammock
    DWG + SLDTL
    Tarp
    WBEdge+SLD TrailH
    Insulation
    HG Econ
    Suspension
    DWG + Sheltowee
    Posts
    113

    Lightweight Quick Release Becket Hitch Suspension Using Dutch Whoopie Hooks

    Total suspension only weight 6.2 oz for both combined.
    Raw cost around $70 with the Dutch hardware costing the most.
    About 1,200 pound support weight.



    Purpose: To allow quick removal of hammock from suspension for packing purposes. This allows becket hitch users to set the hitch and attach/remove hammock as needed. Additionally it reduces rope burn wear on hammock amsteel continous loops.



    Details: Attach the Dutch Clips and tree huggers together and hang from tree as normal. Bowline or figure 8 the mule tape to the tree hugger loops. Install Dutch whoopie hooks to amsteel loops and larks head around mule tape. Set a basic loose Becket hitch around amsteel loop with hook and attach hammock on Dutchware whoopie hook. Do the same for other side then go back and adjust becket hitches and double tie with a half hitch to stop and lock potential slippage. Do this on both sides to get your hangle correct.



    For Hammock Suspension:
    覧覧覧覧覧覧-
    2 x Dutchware Titanium Clips
    2 x Dutchware whoopie Hooks
    2 x 1 wide and 5 long SLD tree huggers
    2 x Mule tape 10 feet
    2 x 7/64th Amsteel loops

    For Tarp Integration:
    覧覧覧覧覧-
    2 x Zing it/lash it loops
    2 x 7/64 amsteel loops
    2 x Dutchware fleaz with zingit loops



    Tarp Details: Larks head zingit and fleaz around tarp. This is a quick attach hardware and also a backup to set tarp up by itself. On suspension, prussik the zingit loops around the mule tape suspension while wrapping around amsteel loop. This makes it easier to slide along suspension.

    /////////////////////////////////////////////////////////////
    UPDATE 11/12/18
    /////////////////////////////////////////////////////////////

    I致e had success with mule tape using just a slippery half hitch as a stopper knot for the larks head so i will be testing some 1/8 th amsteel. Here is the test sketch. Enjoy!



    Tested out 1/8th amsteel and it held fine with slippery half hitch and Dutch whoopie hooks. Tarp does slip a little bit but the hammock held fine. Next will try the UHMWPE and see how that goes.
    Last edited by Papatechie; 11-12-2018 at 18:32.
    "What lies behind us and what lies before us are tiny matters compared to what lies within us" - Ralph Waldo Emerson

Similar Threads

  1. Becket Hitch Suspension; Idea and Questions
    By Tyler in forum Suspension Systems, Ridgelines, & Bug Nets
    Replies: 452
    Last Post: 10-17-2018, 10:56
  2. Whoopie slings MSH or Becket hitch
    By dbolster24 in forum Suspension Systems, Ridgelines, & Bug Nets
    Replies: 15
    Last Post: 11-05-2017, 18:50
  3. Auto lock quick release truckers hitch
    By Tacblades in forum Do-It-Yourself (DIY)
    Replies: 15
    Last Post: 07-20-2017, 17:09
  4. Tarp suspension with becket hitch
    By poorboystooge in forum Weather Protection
    Replies: 15
    Last Post: 03-08-2017, 17:31
  5. Dutch Whoopie Hooks aka 鄭ll-in-one Suspension System
    By PAHikingTrails in forum Dutchware
    Replies: 14
    Last Post: 07-05-2012, 22:41

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •