Just a quick tutorial for my friends at HF.
Final weight of hammock with ridgeline & 6ft whoopies in stuff sack = 20.65oz.
Materials
(from DIY Gear Supply)
1 each- 60” Hammock Blank
3 yds – Noseeum Netting
10 ft - #3 Coil Zipper
2 each - #3 Double Tab Zipper slider
2 ft – 1/8” Reflective Glowwire
1 spool - Gütermann Mara 70
12ft – 1.9mm Tech Line
25ft – 7/64” Amsteel
Total cost = $48.26 + shipping
----------
Net Layout
1. Cut Noseeum to 41” x 81”.
2. Measure in 11.25" from opposite corners and cut to parralelagram shape.
3. Round opposite corners. I use Smurfette's big Tupperware lid. Don't get caught sneaking it out of the kitchen!
4. Decide wheather you want a left lay or right lay and put a little mark at the foot end so you don't get mixed up later.
Diagram is for a right lay when top is facing up. (head left-feet right) If you lay opposite, flip it over now.
----------
Body
1. Mark, pin and sew 3" channels on ends of hammock body with 3 strong rows of stitching.
2. Put a pin in the foot channel so you don't get mixed up later.
----------
Join Net and Body
1. Carefully meassure the distance around the net on the side that will be sewn. Mine ended up about 109.25", but yours may be slightly different.
2. Mark the side to be sewn of the hammock body with a pin at the start and stop of the net stitching.
Note - The net will likely stretch, so leave an inch or two for the net to grow as you sew it. I started the net approx 2" from the end of the channel.
3. Lay Net on top of Body (see diagram) and start pinning it to the hammock body.
4. Stitch the net and body together keeping close to the edge of the rolled hem on the hammock blank.
5. Roll the hem again and add another row of stitching. Hopefully the net is somewhat centered when you finish.
Note - Leave about an inch at the beginning and end unsewn. This will make it easier to attach the zipper.
6. Flip over and run another row of stitching from the inside of the hammock, keeping the net and body stretched taught.
----------
Add Net zipper
1. Place a mark on both halves of your coil zipper, then separate the zipper. The marks will help keep the ends straight.
Note - leave the zipper hang over a few inches at each end and trim it to size later.
2. Start at the head end. Position the net so that the inside is facing up. Position the zipper on the outside of the netting so that the teeth are toward the middle and sticking up toward you. Pin in a couple places so it doesn't move around.
3. Use a zipper foot or the narrowest foot you have. Run a row of stitching along the zipper close to the toothed edge. Keep the zipper and edge of the netting aligned as you go.
4. From the foot end, run a second row of stitching along the face of the zipper. Keep the stitching close to the edge away from the teeth.
----------
Add Body zipper
(see diagrams above)
1. Start at the foot end. Position the body so that the inside is facing up. Position the zipper on the outside of the body so that the teeth are toward the middle and sticking up toward you. Pin in a couple places so it doesn't move around.
2. Use a zipper foot or the narrowest foot you have. Run a row of stitching along the zipper close to the toothed edge. Keep the zipper and edge of the netting aligned as you go.
3. From the head end, run a second row of stitching along the face of the zipper. Keep the stitching close to the edge away from the teeth.
----------
Assemble zipper
1. Bring the 2 ends of the zipper together and install a zipper slide from each end. The net should zip together when the sliders are moved toward the center.
2. Clean up any ragged edges where the zipper, net and body meet by stitching the final inch or so together.
----------
Reinforce ends of channels
1. Bring the channel ends together (from the inside) and run a few stitches back and forth to lock the ends of the channel together.
Note - Failing to do this could result in the net tearing from the channels flexing back and forth.
----------
Finish up
1. Install zipper pulls and cords on zipper slides.
2. Build whoopie slings (see other tutorials). Install by feeding eye bury through each channel and securing with larkshead.
3. Build ridgeline at approx 100" (see other tutorials). Install by feeding through center of hammock and hooking through whoopie slings.
4. Build yourself a stuff sack (see other tutorials).
Disclaimer - This is maybe not the best way or the only way. It's just the way I do it.
Thanks
PapaSmurf
Bookmarks