Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14
  1. #11
    I've done absolutely nothing to it. It was my MIL's machine and it has been in a closet for a dozen years or more.

  2. #12
    Senior Member
    Join Date
    Oct 2012
    Near North, ON
    DIY Bridge db layer 1.1
    DIY 12'
    DIY Climashield
    amsteel/tree strap
    Quote Originally Posted by jaitch View Post
    I've done absolutely nothing to it. It was my MIL's machine and it has been in a closet for a dozen years or more.
    Maybe she put it away a dozen years ago because it was doing then what it's doing now!!

  3. #13
    New Member
    Join Date
    Sep 2012
    Oak Harbor, WA
    DIY and a Lawson
    Poncho liners
    big fat webbing
    Have you felt the motor after it slows down? If the motor is fairly hot or smells like it is hot you may have found your issue. Some of my machines have motors that get relatively hot and tend to slow a bit on prolonged sewing, but friction with lint and built up crap in the works can really cause a motor to work too hard and cause it to slow. After the motor cools the speed comes right back up but then slows again as the overall friction starts to mount again.

    There actually is an oil hole on the majority of sewing machine motors, one on each end right near the shaft entrance and the other near the end cap. A single drop of oil in that hole annually (depending on your usage) can stave off motor bearing failure for a long time.

    The first thing I do when I acquire another machine is run the motor flat out for a bit to see how many sparks the carbons throw and how long it takes to heat up. That usually gives me a pretty good idea of how the machine was used in the past. It also allows you to watch the motor burst into flames if it is clogged up with lint or oil or stuff. (My wife seems to object to me doing that in the house....)

    As mentioned, high belt tension can do the same thing and not allow the machine to reach full speed but is sounds like the belt has not been messed with, so I am up for high load leading to heat build up and slow down.

  4. #14
    Senior Member Ramblinrev's Avatar
    Join Date
    Apr 2008
    Milton, PA
    Hennessey Explorer Ultralight
    Hennessey Hex
    HH Super Shelter
    ring buckle
    If the build up of crud is so bad that it is overloading the motor I would encourage a professional cleaning job. You are likely dealing with stuff that is not just going to brush away. Crud hardens as it sits, then gets soggy as it heats up which bakes it on even more which adds to the stickiness which builds up ad naseum. That's tough to deal with in a home workshop. Get it done right. Plus if bushings are wearing because of the loading and crud build up you really need to have those serviced as well.
    I may be slow... But I sure am gimpy.

    "Bless you child, when you set out to thread a needle don't hold the thread still and fetch the needle up to it; hold the needle still and poke the thread at it; that's the way a woman most always does, but a man always does t'other way."
    Mrs. Loftus to Huck Finn

    We Don't Sew... We Make Gear! video series

    Important thread injector guidelines especially for Newbies

    Bobbin Tension - A Personal Viewpoint

Similar Threads

  1. Looking for a new thread injector
    By boulderv7 in forum Do-It-Yourself (DIY)
    Replies: 7
    Last Post: 10-15-2013, 19:50
  2. Breaking thread on my thread injector?
    By Frost in forum Do-It-Yourself (DIY)
    Replies: 8
    Last Post: 01-29-2012, 08:49
  3. one thread injector that does it all?
    By the_gr8t_waldo in forum Do-It-Yourself (DIY)
    Replies: 8
    Last Post: 09-06-2011, 10:24
  4. Thread Injector thread problems
    By CrazyZippo in forum Do-It-Yourself (DIY)
    Replies: 17
    Last Post: 08-20-2011, 22:24
  5. Thread Injector
    By jeepthangjim in forum Do-It-Yourself (DIY)
    Replies: 6
    Last Post: 10-24-2010, 22:07


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts