Page 1 of 3 123 LastLast
Results 1 to 10 of 23
  1. #1
    New Member raleighbuckner's Avatar
    Join Date
    Nov 2012
    Location
    Greenville, SC
    Hammock
    DIY WBBB Clone
    Posts
    11

    My TurtleDog Stand

    Hello all, I've been lurking around for a while and finally decided to get hanging. I've got quite a few things on the way from DIYGearSupply for making a hammock, but while I'm waiting on it to get here I have to take care of another issue - my backyard has no place to hang from. I'll also be camping some with my son's Webelos Den and I'm not sure if we'll always have soem good trees around.

    So, my first DIY project is making a TurtleDog stand. After reading through all the posts in this thread, I headed out and got the following supplies:

    • 5/16" x 2" bolts (x8)
    • 5/16" fender washers (x8)
    • 5/16" locknuts (x8)
    • 5" heavy duty gate hinges (x2)
    • 3/8" snap links (x2)
    • 3/8" x 3" eye bolts (x2)
    • 3/8" fender washers (x2)
    • 3/8" locknuts (x2)
    • 2" x 2" x 8' pressure treated lumber (x6)
    • 10' 3" (10' 6" counting the taper) 17-gauge chainlink fence top rail (x2)


    Total cost for the supplies was right at $60. Going with regular 2x2s would bring the price down a good bit, but the pressure treated stock was in a whole lot better shape than the regular lumber and I think the treated will hold up a little better anyway.

    Here's the steps I took...

    The Stands

    I wanted the legs to fold pretty closely together, so I started by clamping three of the pieces of wood so I could line up and place the hinges for the two outside legs.



    After drilling the holes and bolting the hinge to the two legs with fender washers and locknuts, I adjusted the center leg down and out a bit to line it up for drilling.



    The center leg gets two bolts, washers and locknuts.



    At this point, I set the first stand up to check out the hinge action. Everything seemed OK,so I went ahead and put the second stand together.



    I am planning to hang the crossbar from the stands similar to hppyfngy's setup except that instead of using an s-hook, I'm using a snap link. The only problem is that the snap link is just a little bigger than the holes in the hinges, so I had to do a quick enlargement with the drill first.



    With that taken care of, the stands were pretty much done until I get my order in from DIYGearSupply and put some limting cordage around the legs to keep them from separating. I also need to cut them down from the full 8' length, but I'll wait and do that once I have something to hang on it.



    The Crossbar

    I only had time to cut the crossbar, I'll have to drill and install the eye bolts later. I cut the two top rails by measuring one 4' and the other 6' from the non-tapered ends.

    The end result is four pieces:

    • 4'
    • 6' 3" (with 3" tapered end for connecting)
    • 6'
    • 4' 3" (with 3" tapered end for connecting)




    With these various piece lengths, I can create a crossbar with the following lengths:

    • 8' 3" (4' + 4' 3")
    • 10' 3" (4' 3" + 6' or 6' 3" + 4')
    • 12' 3" (6' 3" + 6')
    • 14' 6" (6' 3" + 4' 3" + 4')
    • 16' 6" (6' 3" + 6' + 4' 3")
    • 20' 6" (6' 3" + 6' + 4' 3" + 4')


    I'm not sure which length I'll need yet, so the options are good to have.

    Now to wait for the rest of my supplies to come in and get started on the hammock itself. At least now, I'll be able to test it out as I build it.

  2. #2
    olddog's Avatar
    Join Date
    Jan 2011
    Location
    Lakeland, Fl
    Hammock
    WL Snipe
    Tarp
    WL Tadpole
    Insulation
    WL SS UQ, WL SS TQ
    Suspension
    Dutch speedhooks
    Posts
    4,151
    Images
    3
    Good looking stand rb and a great write up.
    Most of us end up poorer here but richer for being here. Olddog, Fulltime hammocker, 365 nights a year.

  3. #3
    Senior Member Fish<><'s Avatar
    Join Date
    Aug 2011
    Location
    Yigo, Guam
    Hammock
    DL1.1XLC/ BIAS WWM/ DIY
    Tarp
    HG Cuben/ DIY
    Insulation
    N/A
    Suspension
    depends...
    Posts
    1,199
    Very well written, and welcome to the forums. I've had my td stand for almost a year, and it still looks like it did the first day I completed it. It is a very well though out design and I really appreciate turtlelady olddog and samsara for all of their work on the portable stand threads.
    "We do not go to the green woods and crystal waters to rough it, we go to smooth it."- G. W. Sears

    My forum name is Fish<><; I'm in the navy; and I hate sleeping on the ground. If I didn't need ground to walk on or measure resistance to, I think I could happily give it up.

  4. #4
    MAD777's Avatar
    Join Date
    May 2009
    Location
    South Florida
    Hammock
    DIY, WBBB &amp; Switchback
    Tarp
    HG cuben,OES Spinn
    Insulation
    DIY down 3/4 UQ/TQ
    Suspension
    Dynaglide &amp; Dutch
    Posts
    10,491
    Images
    39

    My TurtleDog Stand

    Excellent directions, illustrations, and supply list!
    Thanks for making this project easier for everyone that follows you (including me) !
    Mike
    "Life is a Project!"

  5. #5
    Acer's Avatar
    Join Date
    Jul 2011
    Location
    Southern Indiana Wooded Hills
    Hammock
    WBRR, Diy M90 MR Gathered
    Tarp
    WL Tadpole
    Insulation
    Lynx/UGQ/Jarbidge
    Suspension
    Straps/Whoop/Dutch
    Posts
    3,887
    Images
    19
    Its amazing how well these simple stands work. Thanks to all that had alot of imput and design on this stand.

  6. #6

    Join Date
    Nov 2012
    Location
    Jackson, MS
    Hammock
    12' diy hammock
    Tarp
    superfly
    Insulation
    warmth
    Suspension
    cinch buckle
    Posts
    160

    Re: My TurtleDog Stand

    I've been wanting to make one of these for a while now. That is a great write up and supply list! You have motivated me to think about trying to make one. Its too early to be fully motivated, I haven't had my coffee yet.

  7. #7
    Senior Member
    Join Date
    Mar 2010
    Location
    Canton, OH
    Posts
    96
    Zombie thread I know, and I shouldn't critique since I' m right in the middle of blatantly ripping off this desgin ( more or less), but I 'll be danged if I can seehow you get that last 20' sumthin" crossbar length. I can't see it unless you have 3 swedged ends and there only 2 when all is said and done.

    Now, go ahead and tell me to remove my foot from my mouth and point out where I screwed up and missed the pertinent info, because it's entirely likely I've done exactly that.

  8. #8
    Senior Member Strapped-4-Cache's Avatar
    Join Date
    Feb 2010
    Location
    Lawrenceville, GA
    Hammock
    WBBB 1.7 dbl
    Tarp
    GG 12x12
    Insulation
    MM IX dbl
    Suspension
    Webbing
    Posts
    245
    Here ya go... Top Rail Sleeve

  9. #9
    Chigger's Avatar
    Join Date
    Mar 2012
    Location
    Garner, NC
    Hammock
    HHDJ JUNGLE XL(2)
    Tarp
    HH Dia. &amp; Superfly
    Insulation
    TQ HG20* UQ HG20*
    Suspension
    Dutch cinch buckle
    Posts
    511
    Best design and instructions to date hands down. Great job.

  10. #10
    Member
    Join Date
    Jun 2014
    Location
    SE TN
    Hammock
    Warbonnet Traveler 11ft
    Tarp
    Big Daddy
    Insulation
    KAQ Newriver
    Suspension
    Adjustable Webbing
    Posts
    51
    Could you tell me how large an area one tripod takes up? (How large the triangle is) Trying to see if one of these stands will fit in my room or not.

Similar Threads

  1. The TurtleDog stand
    By samsara in forum Do-It-Yourself (DIY)
    Replies: 2541
    Last Post: Today, 01:12
  2. WTB/WTT: Turtledog Stand
    By Zilla in forum Want to Buy
    Replies: 1
    Last Post: 08-19-2014, 18:08
  3. My try at the turtledog stand
    By wylie_coyote in forum Do-It-Yourself (DIY)
    Replies: 28
    Last Post: 08-04-2014, 22:05
  4. Ridgerunner with TurtleDog stand
    By brswan in forum Warbonnet Hammocks
    Replies: 6
    Last Post: 05-18-2014, 22:02
  5. SLS and Turtledog stand
    By gordonfreeman in forum Suspension Systems, Ridgelines, & Bug Nets
    Replies: 13
    Last Post: 10-18-2012, 16:09

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •