Results 1 to 5 of 5
  1. #1
    Senior Member
    Join Date
    Feb 2007
    Location
    Alabama
    Posts
    474

    Non-spreader Bridge Hammock

    I've spent so much time building my pirogue that I haven't spent any time finishing my Bridge Hammock.

    Anyway, I want to try the non-spreader version of this thing. What size and how much Spyderline should I buy to do this right?

  2. #2
    GrizzlyAdams's Avatar
    Join Date
    Apr 2007
    Location
    Illinois
    Hammock
    DIY Bridge, v0.n, where n is large
    Tarp
    depends on season
    Insulation
    DIY UQ
    Posts
    4,628
    Images
    564
    Quote Originally Posted by funbun View Post
    I've spent so much time building my pirogue that I haven't spent any time finishing my Bridge Hammock.

    Anyway, I want to try the non-spreader version of this thing. What size and how much Spyderline should I buy to do this right?
    I've been fine with 2.8mm spyderline, with one exception, where it snapped at a knot. The bridge was in spreaderless configuration, tightened way down, and I wasn't present, so I don't know the circumstances. Because of that though I got 3.8mm for the main suspension (from the top of the suspension triangle to the tree).

    by the numbers

    ridgeline : 16 ft should do. Doesn't need to be spyderline, but I use 2.8mm.
    suspension triangles : 4 x 4.5 ft = 18 ft, 2.8mm.
    side tie-outs : the flatter you can make these lines, the less stress on them. Figure 4 x 8' = 32'.

    That's a total of 16+18+32 = 66 ft.

    A mini-spool from Annapolis Performance Sailing has 75' for $22.95 + shipping (shipping is steep though).

    Grizz

    p.s. (later edit) the tie-outs are not butt-critical and would not need spyderline. Any rope that is good to say, 200 lbs, should be fine there, snapped knot not withstanding (I think there was wind involved in that incident. Or malicious neighborhood kids).
    Last edited by GrizzlyAdams; 11-01-2007 at 09:12. Reason: reduce the spyderline requirements by 1/2

  3. #3
    Senior Member
    Join Date
    Feb 2007
    Location
    Alabama
    Posts
    474
    Cool, thanks. And I assume you're still using snow stakes for the tie outs?

  4. #4
    GrizzlyAdams's Avatar
    Join Date
    Apr 2007
    Location
    Illinois
    Hammock
    DIY Bridge, v0.n, where n is large
    Tarp
    depends on season
    Insulation
    DIY UQ
    Posts
    4,628
    Images
    564
    Quote Originally Posted by funbun View Post
    Cool, thanks. And I assume you're still using snow stakes for the tie outs?
    In this post you will see how I used 2 9" carbon stakes from Titanium Goat (link in that post) at the end of the tie-out. These stakes are amazingly light, 0.25 oz each. Less prone to bend also than the snow stakes. The down-side is price, $15 for 5, you'll need 8. If it turns out that 2 stakes per corner isn't enough you can add as needed with very low impact on weight.

    Grizz

  5. #5
    Quote Originally Posted by GrizzlyAdams View Post
    I've been fine with 2.8mm spyderline, with one exception, where it snapped at a knot.
    3mm is fine for me at 170lbs. 2mm or less on the side tie-outs for the spreading. Heck, even 550 paracord is fine for that.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •