Results 1 to 3 of 3

Hybrid View

  1. #1
    Pro Vagabond's Avatar
    Join Date
    Jul 2010
    Location
    Philly, Pa
    Hammock
    DIY gathered end
    Tarp
    9X11 DIY Syl
    Insulation
    DIY UQ + TQ
    Suspension
    Whoopies + huggers
    Posts
    303

    Some modest advise to noobs from a noob

    Frist of all, I have to say their are many people on here with much more experience that I. I've been "injector thread" for a little over a week, but I've discovered a few tricks that may help out other noobies.

    1. watch all the videos you can from the people on here. Some have been doing this for years and they know what they are talking about.
    2. Research whatever topic and read ALL the threads you can about it to learn from those who know.

    Those are obvious, these are a little more specific to what I've experienced so far:

    1. Even though the gear will be used for outdoor usage, I had trouble with the heavy duty thread. Because the fabric is so thin (excluding webbing), I was getting a lot of "loose" threading as a sewed. Try the lighter thread, but make sure it is 100% poly.
    2. Keep the fabric tight when you are sewing. I'm used to working with wood and steel and you can just let that stuff run through the tool. I have found it might help if you keep a little tension on the fabric as it is going through the machine. I got better stitching and a much better look.
    3. When splicing cordage, the videos and pictorals on this site are GREAT! I follow them to the letter with one modification. I still have my "IN" and "OUT" points for my piece of bent wire, but I feed the wire in the "OUT" point with the loop and come out the "IN" point ready to grab the end. (I hope that makes sense). Instead of taking the point end of the wire and going in the "IN" piont and feeding it through that way, I go the opposite way. For me, I found the curved end of the bent wire cause significantly less damage to the inside of the cord than the pointed end. Trying to make Soft Shackles last night, I tore up a couple peices of cord trying to feed the sharp end through, which brings me to the last point:
    4. Be patient and forgiving. I've been building and creating stuff for 30 years, but never on a "thread injector". I've also never used cord this small before, even though I've whipped and spliced quite a bit in my past. It takes time to get good at anything and I get the impression no one on the site cares if it is perfect. Just make it safe.

    Good luck and keep DIYing!

  2. #2
    Senior Member
    Join Date
    Mar 2009
    Location
    Waynesboro, VA
    Hammock
    DIY bridge, Pertex "Grackle"
    Tarp
    DIY 10x11
    Insulation
    DIY this-n-that
    Suspension
    Whoopie/M-spike
    Posts
    631
    Images
    2
    Great advice, especially about the heavy duty thread. I learned that lesson too, a few years back.

    I'd also add that newcomers should feel free to add their experience or ideas to the pile. Many people have previous professional or hobby experience that could be useful. I think Nacra533 introduced the nacrabiner to us in his very first post! It's exciting to see the community grow and evolve.
    .. truly to enjoy bodily warmth, some small part of you must be cold, for there is no quality in this world that is not what it is merely by contrast. Nothing exists in itself. If you flatter yourself that you are all over comfortable, and have been so a long time, then you cannot be said to be comfortable any more. - Herman Melville

  3. #3
    Senior Member Bradley's Avatar
    Join Date
    Jun 2010
    Location
    West Kootenay, BC
    Hammock
    NX-150 TX-150
    Tarp
    Vertex-Camo
    Insulation
    Z-Liner & DIY Pads
    Suspension
    Clark
    Posts
    1,672
    Good stuff Pro Vagabond

    My Mama would always hold the material well
    both in front and behind the foot
    with an ever so slight tension pulling behind
    and a firm hold but feeding in front.

    There must be a formula for thread thickness vs. material
    just like welding rods and the like,
    but thin and strong for thread.

    My thoughts are: buy as expensive/high-quality as you can IE; machine
    don't cheap out on the thread.
    I won't but things like thread from WM
    but go to the store that sells only sewing materials,
    they should have the best you can get.

    Bradley SaintJohn
    Flat Bottom Canoe
    Start A Biz

    The Transition from Ground Sleeping to Hammocks
    is the Conversion from Agony To Ecstasy,
    and Curing Ground-In-somnia.

    "Call unto me, and I will answer thee, and show you great and mighty things . . ." Jeremiah 33:3
    ΙΧΘΥΣ

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •